PlayStation 2 Mod Chip RIPPER 3

[X-1-ALPHA]

Hy,

ich verkaufe hier einen nagelneuen PlayStation 2 Mod Chip. Es handelt sich dabei um den Ripper 3 auch genannt Sniper 3. Er ist noch original verpackt und mit etwas Zubehör.

Einbauen könnt ihr den Chip in eure PlayStation 2 und in die neue "two" Variante. Letzteres müsst ihr wohl von einem Profi machen lassen da ihr den Chip bzw. er den Chip umflashen muss.

Ja was soll ich noch sagen. Laut Foren ist dies der beste Chip den es zur Zeit auf dem Markt gibt.

Hier mal die Features:

Code [Auswählen] Erweitern


# Full Autodetect and
NoSwap modchip with media Autodetect and intuitive PnP Technology.

# Based on Secure Antifuse Ex Series ACTEL FPGA. Ex Series ACTEL FPGA
is the most SAFE, SECURE and is the LOWEST power consumption (2.5V)
device on the market. It is NOT legacy flash based FPGA/CPLD.


# Absolutely new, rewritten VHDL code with Laser and Laser Coil
protection routines.

# Absolutely new LPPT (Low Power Patching Technique) to save and
PROTECT PS2 motherboard.

# No more MMF (Mysterious Motherboard Failures).

# Reduced power consumption by a factor of 8x. Ripper 3 will not
consume too much power from your console, leaving saved power for
larger HDD and for more stable operation.

# Ground Bounce Free Technology.

# Full PAL and USA NTSC Support. PAL V3..V10 and USA V1..V10. Asian
revision upgrade will be soon.

# No need to press reset once, twice or three times for boot mode
selection. Simply insert CD or DVD and AUTODETECT will do everything
for you. DVD Video, PS2 and PSX are automatically detected by Ripper
3. You can boot from browser, by closing tray, by joypad selection
after entering DEV.olution mode and after returning to browser. BOOT
as you want!

# No need to remember manual for Ripper3!

# Insert and Play Technology.

# 16MB and 32MB third party memory card support without boot CD for
them.

# PSX LOGO position and PSX game screen position are PERFECT and FIXED.

# Everything is AUTO in Ripper3. NO NEED to enter annoying setup/configuration
menus. Ripper3 does everything in it's intelligence.

# HDD (Hard Disc) ATAD patching Support (original HDD or any computer
HDD with unlimited size).

# Free HDLoader support, you can copy your games to HDD with ATAD
support.

# DVD Region FREE.

DEV.olution Mode for loading apps from memory card.

# Only 17/18 wires to solder for PAL consoles and 17/19 wires for NTSC
consoles

# RGB FIX for all consoles.

Two Chip disable functions: Press START and then RESET or legacy
mode 3x reset for convenience and for old, legacy Ripper2 habits.

On screen DISABLE CHIP message. You will know that chip is disabled.

# ULTRA fast PS2 boot (keep pressed the SELECT button and reset) No
more to press anything on JoyPad if you don't like it.

# You can use full automatic features or use legacy Ripper2 booting
technique if you like. No need to configure it and all is intuitive
without configuration. Ripper3 will automatically predict your needs.

# CD/DVD controller requires only 3 wires to be soldered to the bottom
of the motherboard.

# Only "B", "G", "I" wires to the bottom for older PS2 versions.

# Less wires to the laser controller and new patching technology =
longer laser life and NO LA6508 failures, remember new VHDL code!
# Updateable (Re-programmable) Flash Memory Integrated Circuit
supports up to 4Mb on chip.

# 2,5V Very Safe Ripper3 operation and Safe 3,3V power supply.

# 2.5V Very Safe chip operation for more stable and more SAFE
operation. Remember, lower voltage is better!

# Ground Bounce effect is _NOT_ existent.

# It means very easy install without black screen.

# DVD9 compatible.

# Action Replay and Action Replay MAX compatible.

# Disc swapping supported for CD/R media and DVD/R media.

# DivX and MP3 Mediaplayer compatibility.

# Fully compatible and tested with all bios revisions.

# DVDR booting is very fast and reliable with 100% success.

# Absolutely new software suite and only compatible with Ripper3.

# New Ripper3 navigator with new fresh look and many new options.

# New Ripper3 MediapPlayer v1.51 improved for our chip.

# New Ripper3 upgraded Free HDLoader with improved reliability.

# All features work the same on all console motherboards from PAL to
NTSC.

# New look of Ripper3 on blue PCB with gold covered contacts.

# LED testing diode is even more reliable and tests more during
Ripper3 installation.

Chip kostet im Laden knapp 50€ aber ohne Zubehör. Als dreingabe also Zubehör haue ich eine Bauanleitung für alle PlayStation 2 Versionen V1 - V10 auf einer CD mit rauf, Kabel und die Rechnung mit Garantie.

Ihr wollt bestimmt wissen wieso ich den Chip verkaufe wa?

Ich hatte mir bei Ebay eine PS2 gekauft nur wurde ich übers Ohr gehauen und habe jetzt vor kurzem das Geld zum Glück zurück bekommen. Naja und da mir 150€ für eine PlayStation 2 zu viel sind investiere ich es lieber in meinen PC.

Gebt mal eure Gebote ab was ihr ausgeben würdet!

Auf Wunsch könnte ich noch ein Bild ranhängen. Wenn ihr fragen habt dann fragt einfach!

[tf]

ich würde die für den chip mit anleitung 30,-€ geben.
mfg thomas

[X-1-ALPHA]

Sorry Chip wurde schon vor knapp einem Monat für 32€ verkauft!

[timo]

hallo, ich kreig das laufwerk bei meiner ps 2 nemmer auf kann mir da jemand ma die bauanleitung schicken? danke! mfg